Q. In case of spherical bodies with uniform mass distribution, what is the position of center of pressure relative to centre of gravity.

View solution

Q. A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 3.6 m/s². If tank is open at the top then calculate the angle of water surface to the horizontal.

View solution

Q. A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 4.8 m/s². The length of tank is 7 m and depth is 1.5 m. If tank is open at the top then calculate the maximum pressure intensity at the bottom.

View solution

Q. A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 5.5 m/s². The length of tank is 5.5 m and depth is 2 m. If tank is open at the top then calculate the minimum pressure intensity at the bottom.

View solution

Q. A rectangular tank is moving horizontally in the direction of its length with a constant acceleration of 4.5 m/s².The length, width and depth of tank are 7 m, 3m, 2.5m respectively. If tank is open at the top then calculate the total force due to water acting on higher pressure end of the tank.

View solution

Q. A tank containing water upto a depth of 500 mm is moving vertically upward with a constant acceleration of 2.45 m/s². Find the force exerted by fluid of specific gravity 0.65 on the side of tank,width of tank is 1m.

View solution

Q. A tank containing water upto a depth of 750 mm is moving vertically downward with a constant acceleration of 3.45 m/s². Find the force exerted by fluid of specific gravity 0.85 on the side of tank,width of tank is 2m.

View solution

Q. A tank containing water upto a depth of 650 mm is stationary. Find the force exerted by fluid of specific gravity 0.55 on the side of tank,width of tank is 1.5m

View solution

Q. The pressure intensity at the bottom remains same, even if the tank moves with constant horizontal acceleration.

View solution

Q. There will be development of shear stress due to the dynamic motion of tank or container.

View solution

Q. If the tank is moving vertically, which of its component is subjected to maximum total pressure?

View solution

Q. A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the total water pressure (in kN) on the lamina?

View solution

Q. A square lamina (each side equal to 2m) with a central hole of diameter 1m is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the total water pressure (in kN) on the lamina?

View solution

Q. A square lamina (each side equal to 2m) is submerged vertically in water such that the upper edge of the lamina is at a depth of 0.5 m from the free surface. What will be the depth (in m) of the centre of pressure?

View solution

Q. What will be the total pressure (in kN) on a vertical square lamina submerged in a tank of oil (S=0.9) as shown in the figure?

View solution

Q. The upper and lower edges of a square lamina of length 4 m are at a depths of 1 m and 3 m respectively in water. What will be the depth (in m) of the centre of pressure?

View solution

Q. The upper and lower edges of a square lamina of length 4 m are at a depths of 1 m and 3 m respectively in water. What will be the total pressure (in kN) on the lamina?

View solution

Q. What will be the depth (in m) of the centre of pressure for a vertical square lamina submerged in a tank of oil (S=0.8) as shown in the figure?

View solution

Q. The greatest and the least depth of a circular plate of 4 m diameter from the free surface of water are 3 m and 1 m respectively as shown. What will be the total pressure in (kN) on the plate?

View solution

Q. The greatest and the least depth of a circular plate of 4 m diameter from the free surface of water are 3m and 1 m respectively as shown. What will be the depth (in m) of it’s centre of pressure?

View solution