Question
a.
Power can be measured by this method only for star connected loads
b.
When two wattmeters have equal readings power factor is 0.5.
c.
When power factor is 1, one of the wattmeters readings is zero
d.
When the two wattmeter read equal and opposite, p.f. is zero.
Posted under Electronics and Communication Engineering
Interact with the Community - Share Your Thoughts
Uncertain About the Answer? Seek Clarification Here.
Understand the Explanation? Include it Here.
Q. Which of the following statement is correct for two wattmeters method of power measurement in 3 phase circuit?
Similar Questions
Explore Relevant Multiple Choice Questions (MCQs)
Q. In a thermocouple temperature transducer, the output voltage is usually measured by
View solution
Q. A moving iron instrument gives correct reading when used at
View solution
Q. Induction wattmeter can be used in
View solution
Q. A meter has a square law scale. For 2 A current the deflection in 90°. For a deflection of 45°, the current is
View solution
Q. Consider the following Statements regarding resistance strain gauge
1. The gauge factor is in the range of 2 to 5.
2. The resistance changes due to change in specific resistance with strain.
3. The resistance increases with increase in temperature.
Of the above statements, which are correct?
View solution
Q. PCM employing 4 bit code is used to send data having frequency range from 0 to 2 kHz. The minimum required bandwidth of carrier channel is
View solution
Q. A sinusoidal ac voltage of amplitude 100 V is applied to a rectifying device which offers 10 Ω resistance in forward direction and infinite resistance in reverse direction. The reading on hot wire ammeter will be
View solution
Q. When a capacitor is connected to the terminals of an ohmmeter, the pointer indicated a low resistance initially and finally come to infinity position. This shows that capacitor is
View solution
Q. Consider the following operation in respect of Wheatstone bridge (Kb, denotes battery key, Kg denotes galvanometer key)
1. open Kb
2. close Kg
3. close Kb
4. open Kg
The correct sequence of operations is
View solution
Q. Two voltmeters 0-250 V each having resistances of 5 kΩ and 10 kΩ respectively and are connected in series. To ensure that neither of them goes beyond scale the total voltage which can be applied should be less than
View solution
Q. A 24 mm long conductor has a resistance of 128 Ω. The change in resistance is 13.3 Ω and change in length is 1.6 mm under tension. The gauge factor is
View solution
Q. Measuring of unknown voltage with a dc potentiometer loses its advantage of open circuit measurement when
View solution
Q. In a digital measuring device the input electrical signal is in the frequency range of dc to ac (50) Hz. It must be sampled at a rate of
View solution
Q. The volt ratio box is basically a
View solution
Q. A sinusoidal ac voltage of amplitude 100 V is applied to a rectifying device which offers 10 Ω resistance in forward direction and infinite resistance in backward direction. A moving coil ammeter is also connected in the circuit. The reading of ammeter will be
View solution
Q. A variable reluctance tachometer has 180 teeth on rotor. The speed of shaft on which it is mounted in 1200 rpm. The frequency of output pulses is
View solution
Q. Assertion (A): Wien bridge can be used for measuring frequency.
Reason (R): A frequency meter for 50 Hz system has a frequency range of 40 to 60 Hz.
View solution
Q. Which of these has poor overload capacity?
View solution
Q. In 3 phase power measurement by two wattmeter method, both wattmeters had equal reading. The power factor of load is
View solution
Q. Which instrument is based on induction principle?
View solution
Recommended Subjects
Are you eager to expand your knowledge beyond Electronics and Communication Engineering? We've handpicked a range of related categories that you might find intriguing.
Click on the categories below to discover a wealth of MCQs and enrich your understanding of various subjects. Happy exploring!