#### Question

a.

1:√3:2

b.

1:2:3

c.

1:2:2

d.

1:√2:√2

Posted under Fluid Mechanics Basic Chemical Engineering

#### Interact with the Community - Share Your Thoughts

Uncertain About the Answer? Seek Clarification Here.

Understand the Explanation? Include it Here.

###### Q. Three piping networks as shown in the figure are placed horizontally. They are made using identical pipe segments and are subjected to the same pressure drop across them. Assuming...

## Similar Questions

###### Explore Relevant Multiple Choice Questions (MCQs)

Q. For flow through an orifice from a reservoir, the actual velocity at the vena con-tracta is given by

View solution

Q. Which of the following is the 'Blaussius equation', relating friction factor to the Reynolds number ?

View solution

Q. The energy equation, given by following equation, where (E = internal energy/mass), is applicable to

View solution

Q. What is the ratio of fluid carrying capacity of two pipes having diameters d₁ and d₂ respectively ?

View solution

Q. The equivalent diameter for flow through a rectangular duct of width B and height H is

View solution

Q. Pick out the Hagen-Poiseulle's equation.

View solution

Q. During fluid flow, variation of shear stress(τ) with velocity gradientat (dv/dy) constant pressure temperature is shown below in the figure. In the below figure, Binghom plastic is represented by the curve .

View solution

Q. Which is the correct relationship for a centrifugal pump ? (where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm)

View solution

Q. The location of centre of pressure, which defines the point of application of the total pressure force on the surface, can be calculated by applying the principle of moments according to which "sum of the moment of the resultant force about an axis is equal to the sum of the components about the same axis". The centre of pressure of a rectangular surface (of width 'w') immersed vertically in a static mass of fluid is at a depth of(where, y = depth of the liquid)

View solution

Q. A centrifugal pump is used to pump water through a horizontal distance of 150 m, and then raised to an overhead tank 10 m above. The pipe is smooth with an I.D of 50 mm. What head (m of water) must the pump generate at its exit (E) to deliver water at a flow rate of 0.001 m³/s? The Fanning friction factor, f is 0.0062.

View solution

Q. Pick out the Kozney-Karman equation (valid for low Nʀₑ) for fluid flow through a packed bed of solids.

View solution

Q. Characteristic curves for a centrifugal pump plotted against its capacity is shown in the diagram. x, y and z denote respectively

View solution

Q. Specific speed for a centrifugal pump is

View solution

Q. For flow through a venturi at a particular discharge, the correct relationships among velocities at point X, Y and Z would be

View solution

Q. In frictional fluid flow, the following quantity is

View solution

Q. What is the force required (in Newtons) to hold a spherical balloon stationary in water at a depth of H from the air-water iterface? The balloon is of radius 0.1 m and is filled with air.

View solution

Q. For the manometer set up shown in the figure, the pressure difference Pᴀ - Pʙ is given by

View solution

Q. Drag co-officient Cᴅ, in Stoke's law range is given by

View solution

Q. In power law, consider the following equation, then the fluid is

View solution

Q. The equivalent diameter for pressure drop calculation for a fluid flowing through a rectangular cross-section channels having sides 'x' & 'y' is given by

View solution

# Recommended Subjects

Are you eager to expand your knowledge beyond Basic Chemical Engineering? We've handpicked a range of related categories that you might find intriguing.

Click on the categories below to discover a wealth of MCQs and enrich your understanding of various subjects. Happy exploring!