Q. On a heat transfer surface, fins are provided to

View solution

Q. In heat dissipation from an infinitely long fin, the boundary conditions are

View solution

Q. The temperature distribution in case of infinitely long fin is

View solution

Q. The rate of heat transfer in case of infinitely long fin is given by

View solution

Q. Let us say there are two rods having same dimensions, one made of brass (k = 85W/m K) and the other of copper (k = 375W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm away from the furnace, the temperature of brass rod is 120 degree Celsius. Find the distance at which the same temperature would be reached in the copper rod? Both ends are exposed to the same environment

View solution

Q. Three rods, one made of silver (l = 420W/m K), second made of aluminum (k = 210W/m K) and the third made of iron (k = 70W/m K) are coated with a uniform layer of wax all around. The rods are placed vertically in a boiling water bath with 250 mm length of each rod projecting outside. If all the rods are having following dimensions i.e. diameter = 15 mm and length = 300 mm and have identical surface coefficient 12.5W/ m² K, work out the ratio of lengths up to which wax will melt on each rod

View solution

Q. A rod of 10 mm square section and 160 mm length with thermal conductivity of 50W/m K protrudes from a furnace wall at 200 degree Celsius with convective coefficient 20 W/ square m K. Make calculations for the heat convective up to 80 mm length

View solution

Q. A fin protrudes from a surface which is held at a temperature higher than that of its environment. The heat transferred away from the fin is

View solution

Q. The value of correction length for equilateral fin is

View solution

Q. The parameter m = (h P/k A C)^1/2 has been stated to increase in a long fin. If all other parameters are constant, then

View solution

Q. The relevant boundary conditions in case of heat dissipation from a fin insulated at the tip are

View solution

Q. The temperature distribution in case of fin insulated at the tip is given by

View solution

Q. The rate of heat transfer from the fin in case of fin insulated at the tip is

View solution

Q. “Fin is insulated at the tip”. What does that mean?

View solution

Q. Find the heat transfer rate from a hot surface for 6 fins of 10 cm length? The base temperature of the fin is maintained at 200 degree Celsius and the film is exposed to a convection environment at 15 degree Celsius with convective coefficient 25W/square m K. Each fin has cross-sectional area 2.5 square centimeter and is made of a material having thermal conductivity 250W/m K

View solution

Q. An electronic semiconductor device generates 0.16 k J/hr of heat. To keep the surface temperature at the upper safe limit of 75 degree Celsius, it is desired that the heat generated should be dissipated to the surrounding environment which is at 30 degree Celsius. The task is accomplished by attaching aluminum fins, 0.5 square mm and 10 mm to the surface. Work out the number of fins if thermal conductivity of fin material is 690W/m K and the heat transfer coefficient is 45k J/square m hr K. Neglect the heat loss from the tip of the fin

View solution

Q. A rod of 10 mm diameter and 80 mm length with thermal conductivity 16W/ m K protrudes from a surface at 160 degree Celsius. The rod is exposed to air at 30 degree Celsius with a convective coefficient of 25W/square m K. How does the heat flow from this rod get affected if the same material volume is used for two fins of the same length? Assume short fin with insulated end

View solution

Q. Two rods A and B of the same length and diameter protrude from a surface at 120 degree Celsius and are exposed at air at 25 degree Celsius. The temperatures measured at the end of the rods are 50 degree Celsius and 75 degree Celsius. If thermal conductivity of material A is 20W/ m K, calculate it for B.

View solution

Q. An centrifugal pump which circulates a hot liquid metal at 500 degree Celsius is driven by a 3600 rpm electric motor. The motor is coupled to the pump impeller by a horizontal steel shaft of dia 25 mm. Let us assume the motor temperature as 60 degree Celsius with the ambient air at 25 degree Celsius, what length of shaft should be specified between the motor and the pump? It may be presumed that the thermal conductivity of the shaft material is 35W/m K, and that the convective film coefficient between the steel shaft and the ambient air is 15.7W/square m K

View solution

Q. The utility of fin in dissipating a given quantity of heat is generally assessed on the basic of how many parameters?

View solution