Q. The temperature and rate of heat conduction are undoubtedly dependent on

View solution

Q. Glass spheres of 2 mm radius and at 500 degree Celsius are to be cooled by exposing them to an air stream at 25 degree Celsius. Find the minimum time required for cooling to a temperature of 60 degree Celsius. Assume the following property values

Density = 2250 kg/m³

Specific heat = 850 J/kg K

Conductivity = 1.5 W/m K

View solution

Q. Which is true regarding lumped system analysis?
(i) Conductive resistance = 0

(ii) Convective resistance = 0

(iii) Thermal conductivity = 0

(iv) Thermal conductivity = infinity

Identify the correct statements

View solution

Q. Which of the following is an example of lump system analysis?

View solution

Q. What is the criterion for the applicability of lump system analysis?

View solution

Q. What is the value of characteristics length for cylinder?

View solution

Q. During heat treatment, cylindrical pieces of 25 mm diameter, 30 mm height and at 30 degree Celsius are placed in a furnace at 750 degree Celsius with convective coefficient 80 W/m² degree. Find the value of biot number if thermal conductivity is 40 W/m degree

View solution

Q. What is the value of characteristics length for sphere?

View solution

Q. What is the value of characteristics length for cube?

View solution

Q. “An infinite solid is one which extends itself infinitely in all directions of space”. Identify the correct option

View solution

Q. The boundary conditions in case of transient heat conduction in infinite thick solids are

(i) t (x = 0) = t i
(ii) t (0, T) = t a for T greater than zero
(iii) t (infinity, T) = t i for T greater than zero
Identify the correct statements

View solution

Q. The perturbation time varies as

View solution

Q. The temperature perturbation at all the surface has penetrated to the depth (Where, T is time constant and α is thermal diffusivity.)

View solution

Q. At the penetration depth d, there will be 1% perturbation at a time given by

View solution

Q. A large steel ingot, which has been uniformly heated to 750 degree Celsius, is hardened by quenching it in an oil bath that is maintained at 25 degree Celsius. What length of time is required for the temperature to reach 600 degree Celsius at a depth of 1 cm? Thermal diffusivity for the steel ingot is 1.21 * 10¯⁵ m²/s. The ingot may be approximated as a flat plate

View solution

Q. A mild steel plate 5 cm thick and initially at 40 degree Celsius temperature is suddenly exposed on one side to a fluid which causes the surface temperature to increase to and remain at 90 degree Celsius. Calculate maximum time that the slab be treated as a semi-infinitely body
For steel, thermal diffusivity = 1.25 * 10¯⁵ m²/s

View solution

Q. Water pipes are to be buried underground in a wet soil (thermal diffusivity = 2.78 * 10¯³ m²/s) which is initially at 4.5 degree Celsius. The soil surface temperature suddenly drops to -5 degree Celsius and remains at this value for₁0 hours. Calculate the minimum depth at which the pipe be laid if the surrounding soil temperature is to remain above 0 degree Celsius. The soil may be considered as semi-infinite solid

View solution

Q. When the surface temperature variation inside a solid are periodic in nature, the profile of temperature variation with time may assume

View solution

Q. The surface temperature oscillates about the mean temperature level in accordance with the relation

View solution

Q. The temperature variation of a thick brick wall during periodic heating or cooling follows a sinusoidal waveform. During a period of 24 hours, the surface temperature ranges from 25 degree Celsius to 75 degree Celsius. Workout the time lag of the temperature wave corresponding to a point located at 25 cm from the wall surface. Thermo-physical properties of the wall material are; thermal conductivity = 0.62 W/m K; specific heat = 450 J/kg K and density = 1620 kg/m³

View solution