Question

Decrease in p.f. makes Vₛ to lead Vₚ.

a.

True

b.

False

c.

May be True or False

d.

Can't say

Answer: (a).True

Interact with the Community - Share Your Thoughts

Uncertain About the Answer? Seek Clarification Here.

Understand the Explanation? Include it Here.

Q. Decrease in p.f. makes Vₛ to lead Vₚ.

Similar Questions

Explore Relevant Multiple Choice Questions (MCQs)

Q. At constant voltage how is frequency affected by flux?

Q. A 50 Hz, bar primary CT has a secondary with 800 turns. The secondary supplies 7 A current into a purely resistive burden of 2 Ω. The magnetizing ampere-turns are 300. The phase angle is?

Q. A 50 Hz, bar primary CT has a secondary with 500 turns. The secondary supplies 5 A current into a purely resistive burden of 1 Ω. The magnetizing ampere-turns are 200. What is the ratio error at full load, if the iron loss is 1.5 W and magnetizing mmf is 100 A?

Q. A 1000/5 A, 50 Hz correct transformer has a secondary burden comprising a non-inductance of 1.6Ω. The flux in the core at full load is?

Q. A 1000/5 A, 50 Hz correct transformer has a secondary burden comprising a non-inductance of 2Ω. What is the ratio error, if the iron loss is 3 W and magnetizing mmf is 250 A?

Q. A 200/1 Current Transformer (CT) is wound with 400 turns on the secondary on a toroidal core. When it carries a current of 180 A on the primary, the ratio is found to be -0.5%. If the number of secondary turns is reduced by 1, the new ratio error (in %) will be?

Q. A (350 A/ 7A), 50 Hz current transformer has a primary bar. The secondary burden is a pure resistance of 1 Ω and it draws a current of 5 A. The magnetic core requires 350 AT for magnetization. Find the percentage ratio error.

Q. The observation when the secondary winding of a current transformer is open-circuited is?

Q. Usually a CT has ____________

Q. A PT is a device which is ___________

Q. The CT supplies current to the current coil of a wattmeter power factor meter, energy meter and, an ammeter. These are connected as?

Q. In a moving iron meter, the deflection torque is proportional to?

Q. The full-scale deflection current of an ammeter is 4 mA and its internal resistance is 400Ω. If this meter is to have a full deflection of 10 A, what is the value of the shunt resistance to be used?

Q. The full-scale deflection current of a meter is 4 mA and its internal resistance is 400Ω. This meter is to have full deflection when 400 V is measured. What is the value of the series resistor to be used?

Q. Two ammeters, one with a full-scale current of 1 mA and internal resistance of 100 Ω and other a full-scale current of 10 mA and internal resistance of 25 Ω are in parallel. What is the total current, these two meters can carry without the reading out of scale in any meter?

Q. A meter has a full scale of 90° at a current of 1 A. This meter has a perfect square law response. What is the current when the deflection angle is 45°?

Q. The scale of a dynamometer type instrument marked in terms of RMS value would be__________

Q. Moving Iron Instrument can be used as ____________

Q. A 10 mA PMMC ammeter reads 4 mA in a circuit. Its bottom control spring snaps suddenly. The meter will now show __________

Q. The standardization of AC potentiometer is done by ____________

Recommended Subjects

Are you eager to expand your knowledge beyond Electrical Measurement and Instrumentation? We've handpicked a range of related categories that you might find intriguing.

Click on the categories below to discover a wealth of MCQs and enrich your understanding of various subjects. Happy exploring!