Unit of specific resistance is


Ohm mm²/m


Ohm mm




Ohm mm/m

Answer: (a).Ohm mm²/m

Interact with the Community - Share Your Thoughts

Uncertain About the Answer? Seek Clarification Here.

Understand the Explanation? Include it Here.

Q. Unit of specific resistance is

Similar Questions

Explore Relevant Multiple Choice Questions (MCQs)

Q. What maximum thickness of concrete can be poured without causing the temperature gradient to exceed 98.5 degree Celsius per meter anywhere in the slab? Consider a 1.2 m thick slab of poured concrete (k = 1.148 W/m degree) with both of side surfaces maintained at a temperature of 20 degree Celsius. During its curing, chemical energy is released at the rate of 80 W/m³. Workout the maximum temperature of concrete

Q. Dielectric heating apparatus consists of

Q. A slab of insulating material of thickness 6 cm and thermal conductivity 1.4kJ/m hr deg is placed between and is in contact with two parallel electrodes, and is then subjected to high frequency dielectric heating at a uniform rate of 140,000kJ/m³ hr. At steady state coefficients of combined radiation and convection are 42 and 48 kJ/m² hr deg. If atmospheric temperature is 25 degree Celsius, find surface temperatures?

Q. A 25 mm diameter egg roll (k = 1 W/m degree) is roasted with the help of microwave heating. For good quality roasting, it is desired that temperature at the center of roll is maintained at 100 degree Celsius when the surrounding temperature is 25 degree Celsius. What should be the heating capacity in W/m³ of the microwave if the heat transfer coefficient on the surface of egg roll is 20 W/m² degree?

Q. The constants of integration are to be determined from the relevant boundary conditions which are
(i) t = t w at r = R
(ii) q g (π L R²) = -k (2 π R L) (d t/d r)
(iii) Increasing temperature gradient
Choose the correct option?

Q. A concrete column used in bridge construction is cylindrical in shape with a diameter of 1 meter. The column is completely poured in a short interval of time and the hydration of concrete results in the equivalent of a uniform source strength of 0.7 W/kg. Determine the temperature at the center of the cylinder at a time when the outside surface temperature is 75 degree Celsius. The column is sufficiently long so that temperature variation along its length may be neglected. For concrete
Average thermal conductivity = 0.95 W/m K
Average density = 2300 kg/m³

Q. The temperature distribution profile for a solid cylinder is

Q. A slab of 12 cm thickness and generating heat uniformly at 10⁶ W/m³ has thermal conductivity of 200 W/m degree. Both surfaces of the slab are maintained at 150 degree Celsius. Determine the heat flow rate at the quarter planes

Q. Consider a convective heat flow to water at 75 degree Celsius from a cylindrical nuclear reactor fuel rod of 50 mm diameter. The rate of heat generation is 50000000 W/m³ and convective heat transfer coefficient is I kW/m² K. The outer surface temperature of the fuel element would be

Q. For a cylindrical rod with uniformly distributed heat sources, the thermal gradient at half the radius location will be

Q. Consider heat conduction through a solid sphere of radius R. There are certain assumptions

(i) Unsteady state conditions
(ii) One-dimensional radial conduction
(iii) Constant thermal conductivity

Identify the correct statements

Q. An 8 cm diameter orange, approximately spherical in shape, undergoes ripening process and generates 18000 k J/m³ hr of energy. If external surface of the orange is at 6.5 degree Celsius, find out the temperature at the center of the orange. Take thermal conductivity = 0.8 k J/ m hr degree for the orange material

Q. A solid sphere of 8 cm radius has a uniform heat generation of 4000000 W/m³. The outside surface is exposed to a fluid at 150 degree Celsius with convective heat transfer coefficient of 750 W/m² K. If thermal conductivity of the solid material is 30 W/m K, determine maximum temperature

Q. Identify the correct boundary condition for a hollow sphere with inside surface insulated.

Q. A hollow sphere (k = 30 W/m K) of inner radius 6 cm and outside radius 8 cm has a heat generation rate of 4000000 W/m³. The inside surface is insulated and heat is removed by convection over the outside surface by a fluid at 100 degree Celsius with surface conductance 300 W/m² K. Make calculations for the temperature at the outside surfaces of the sphere

Q. A composite slab consists of 5 cm thick layer of steel (k = 146 kJ/m hr degree) on the left side and a 6 cm thick layer of brass (k = 276 kJ/m hr degree) on the right hand side. The outer surfaces of the steel and brass are maintained at 100 degree Celsius and 50 degree Celsius. The contact between the two slabs is perfect and heat is generated at the rate of 4.2 * 10⁵ k J/m² hr at the plane of contact. The heat thus generated is dissipated from both sides of composite slab for steady state conditions. Calculate the temperature at the interface

Recommended Subjects

Are you eager to expand your knowledge beyond Heat Transfer? We've handpicked a range of related categories that you might find intriguing.

Click on the categories below to discover a wealth of MCQs and enrich your understanding of various subjects. Happy exploring!