Steel Structure Design MCQs

Welcome to our comprehensive collection of Multiple Choice Questions (MCQs) on Steel Structure Design, a fundamental topic in the field of Civil Engineering. Whether you're preparing for competitive exams, honing your problem-solving skills, or simply looking to enhance your abilities in this field, our Steel Structure Design MCQs are designed to help you grasp the core concepts and excel in solving problems.

In this section, you'll find a wide range of Steel Structure Design mcq questions that explore various aspects of Steel Structure Design problems. Each MCQ is crafted to challenge your understanding of Steel Structure Design principles, enabling you to refine your problem-solving techniques. Whether you're a student aiming to ace Civil Engineering tests, a job seeker preparing for interviews, or someone simply interested in sharpening their skills, our Steel Structure Design MCQs are your pathway to success in mastering this essential Civil Engineering topic.

Note: Each of the following question comes with multiple answer choices. Select the most appropriate option and test your understanding of Steel Structure Design. You can click on an option to test your knowledge before viewing the solution for a MCQ. Happy learning!

So, are you ready to put your Steel Structure Design knowledge to the test? Let's get started with our carefully curated MCQs!

Steel Structure Design MCQs | Page 10 of 24

Discover more Topics under Civil Engineering

Q91.
The maximum axial load which is just sufficient to keep a column in a small deflected shape, is called

a.

crippling load

b.

buckling load

c.

critical load

d.

all the above.

Discuss
Answer: (d).all the above.
Q92.
If the slenderness ratio is greater than 160, the allowable stress in axial compression is multiplied by a factor (1.2 - (l/xy) where x is

a.

200

b.

400

c.

600

d.

800

Discuss
Answer: (d).800
Q93.
The effective length of a compression member of length L, held in position and restrained in direction at both ends, is

a.

L

b.

0.67 L

c.

0.85 L

d.

1.5 L

Discuss
Answer: (b).0.67 L
Q94.
Spans of continuous fillers are considered approximately equal if the longest span does not exceed the shortest span by more than

a.

5%

b.

10%

c.

15%

d.

20%

Discuss
Answer: (c).15%
Q95.
The gross diameter of a rivet is the diameter of

a.

cold rivet before driving

b.

rivet after driving

c.

rivet hole

d.

none of these.

Discuss
Answer: (b).rivet after driving
Q96.
The effective length L of a simply supported beam with ends restrained against torsion, and also the ends of compression flange partially restrained against lateral bending, is given by

a.

L = span

b.

L = 0.85 span

c.

L = 0.75 span

d.

L = 0.7 span

Discuss
Answer: (b).L = 0.85 span
Q97.
Rolled steel beams are designated by Indian Standard series and its

a.

weight per metre and depth of its section

b.

depth of section and weight per metre

c.

width of flange and weight per metre

d.

weight per metre and flange width.

Discuss
Answer: (b).depth of section and weight per metre
Q98.
The spans are considered approximately equal if the longest span does not exceed the shortest span by more than

a.

5%

b.

10%

c.

15%

d.

20%

Discuss
Answer: (c).15%
Q99.
If the depth of the section of an upper column is smaller than the lower column

a.

filler plates are provided with column splice

b.

bearing plates are provided with column splice

c.

neither filler plates nor bearing plates are provided with column splice

d.

filler plates and bearing plates are provided with column splice

Discuss
Answer: (d).filler plates and bearing plates are provided with column splice
Q100.
A tension member, if subjected to possible reversal of stress due to wind, the slenderness ratio of the member should not exceed

a.

180

b.

200

c.

250

d.

350

Discuss
Answer: (d).350
Page 10 of 24